Fire Engineering Training Community

Where firefighters come to talk training

Do you run stack tips or a fog nozzle on the wagon pipe and why??

Views: 1183

Replies to This Discussion

Can you clarify what a Wagon Pipe Nozzle is to us folks out in the West? If it is an elevated Master Stream that is fixed to the top of your Engine, than yes we do. Salt Lake uses stacked tips ranging from 2" to 1 1/8". It could be smaller I am not 100% sure. Our Master Streams are set up to be removed and placed on the ground for remote multiversal applications. eg. LCG tanks, tank cars, reverse lays, etc. It could be manned or unmanned. Hope this helps.
Eric
lol..We run stacked tips on or deckguns on our Engine.. We do have fogs but they sit in the compartment. We have the stacked tips so we can hit it hard with reach and GPM. Blitz attack etc. If its a fully envoled fire why not put what you have on it fast.

We too can make them ground monitors in which we too can put on the Fog/Combo for HAZ-MAT situations.
thanks guys. i have a few arguing the fact of the fog for exposure protection vs. doing damage to the exposure with the straight tips. We run tips on our rig, but some think the fog is the desirable tip. I feel that radiant heat will penetrate the fog curtain type pattern with this applaication and the water would be better used by directly wetting the exposure and putting some on the fire.
We run with fog nozzles on our deck guns, but, the faithfull stack tips are always close. Depending on the incident type or need, we have no problem changing over. Different incidents call for different nozzles.

Terminology always amazes me as how it changes, from place to place and how the vernacular differs. Anyway, here in the NE Rustbelt, a master stream mounted permanently to the apparatus, (but not an elevated master stream as in a piped ladder or elevated platform) we would call a deck gun. A master stream that is fed by large diameter hose, LDH (or we would simply call it supply hose) that is intended to be portable and run from a flat surface, such as the ground or a flat roof top we call a "Stang Gun", but this is a trade name. These are good for getting to remote locations where we can't take a rig, such as alleys and rear yards. An elevated master stream is a piped aerial ladder or elevated platform and is called, well, an elevated master stream of course! Smaller versions of portable deck guns, such as the "Blitzfire" which takes its' supply from 2.5" hose are not truly master streams, as the gallonage doesn't meet the requirements for a master stream, are very handy tools indeed. We keep both stacked and TFT tips with them, and they are a great choice for exposures because once they are set up, they can be left unmanned if you're shorthanded or manned by just one guy and they don't rob too much from the water demand equation. Wiith that said, onto Jims question.....

   You're right, Jim, radiant heat will penetrate your fog stream if it's used like a curtain, but if you're putting it directly on the exposure, making the exposure wet, it should do the job. A smoothbore tip directly on the exposure will probably do some damage. On our Sutphen buckets we have dual appliances, so we have one smoothbore and one TFT Master. We keep the TFT Master on our piped aerial ladders. We can substitute a smoothbore, but it takes time and there is usually no need to. Our Stang Guns can have either one, and is usually stored with no tip because of compartment space.

   All of our master stream appliances are capable of 1000 gpm flows and with a smoothbore tip are capable of doing a great deal of damage. We need FG Commands approval to use them. On the negative side, they can buckle walls, topple chimneys and send roofing materials great distances. On the positive side, they have great reach and penetration for getting deep into structures and are quite suitable to very large structures such as factories and churches and warehouses, provided some care is taken in where they are pointed. They are also quite handy when there is a need to strip an asphalt roof and boards when you can't risk putting a team on the roof the conventional way. Needless to say, this only happens when the building is empty of all personell, and we always tell those on the fireground before we deploy so they can get their visors down and hopefully behind something, a tree or an outbuilding, because when you've seen this "unroofing" process from a bucket, it is truly awesome, the kind of power you are unleashing. TJP

RSS

Policy Page

PLEASE NOTE

The login above DOES NOT provide access to Fire Engineering magazine archives. Please go here for our archives.

CONTRIBUTORS NOTE

Our contributors' posts are not vetted by the Fire Engineering technical board, and reflect the views and opinions of the individual authors. Anyone is welcome to participate.

For vetted content, please go to www.fireengineering.com/issues.

We are excited to have you participate in our discussions and interactive forums. Before you begin posting, please take a moment to read our community policy page.  

Be Alert for Spam
We actively monitor the community for spam, however some does slip through. Please use common sense and caution when clicking links. If you suspect you've been hit by spam, e-mail peter.prochilo@clarionevents.com.

FE Podcasts


Check out the most recent episode and schedule of
UPCOMING PODCASTS

Groups

© 2024   Created by fireeng.   Powered by

Badges  |  Report an Issue  |  Terms of Service