Fire Engineering Training Community

Where firefighters come to talk training

Ventilating Attic Fires With Solar Panels

By Brian Butler

We are currently starting to see more photovoltaic (PV) solar panels on the roofs in urban area housing, especially in New Jersey which has the most solar panels per square mile in the U.S.  PV solar panels will be problematic when performing roof ventilation and ladder placement. In addition, the panels are always energized and their added weight may contribute to and accelerate collapse.

Solar panels cannot realistically be deenergized during fire operations unless correctly powered down and all panels completely covered with appropriate canvas or 100 percent light-blocking tarps. Firefighters are going to have to CAREFULLY deal with their presence and focus on isolation over deenergizing. PV solar panels are always live and can easily electrocute a complacent firefighter using a hand tool and roof ladder in their vicinity.

The primary concerns for the presence of panels during attic fires vary from electrocution, roof ventilation and the weight of the panels contributing to collapse. An array of panels weighting 150 lbs each, and carrying voltage between 500-1000 volts DC current are dangers the IC must consider. Another concern is overhaul. The electrical components (solar PV conduits and wiring) may extend into the attic space. When shutting off the breaker to secure the buildings power prior to opening up, hooks are being extended into an area that is potentially energized.

TIP: Truck firemen assigned to the roof and operating saws must avoid the panels, conduit, and wiring area when cutting the vent-h***. If panels are starting to burn, the acrid smoke is deadly and contains additional hazardous material. Wear an SCBA when solar panels are present! (Usually, I am against SCBA's on the roof, but not for solar panels)

The presence of 20 PV solar panels on a lightweight truss roof with fire in the attic or cockloft will be adding 3000 lbs to the roof, plus the weight of the firemen. There could be several inches of snow covering an array of solar panels on the roof at a top floor fire in a SFD with unsuspecting firemen below unaware of this additional weight.

IMPORTANT: Heavy solar panels sliding off the roof can kill firefighters below. Safety officers must address the potential for runaway panels at large fires, and keep those areas clear.

(Above) Solar panels are usually placed on one side of the roof, the side closest to achieving 180′ south. This location helps capture the maximum amount of thermal energy throughout the year. Vertical ventilation for an attic or cockloft fire can still be achieved by using the opposite side of the roof well below the ridge using extreme CAUTION to avoid conduits, wiring systems and the panels themselves. If that’s not effective or possible, the presence of a firewall combined with good horizontal ventilation might save the exposures.

Approximately 7% of solar panels are installed incorrectly.

Although rare occurrences, solar panels have started attic fires.

Another concern with solar power are solar shingles on the roof. Though not as common as PV panels, it eliminates altogether the possibility of venting the roof at top floor fires.

Photo by Brian Butler

For steep pitch roofs, work from an aerial device and vent the opposite side where no panels are present.

All firefighters should attend a course on solar panels to become familiar with them. The technology is always changing and the dangers are always going to be there for the duration of their careers.

Views: 2699

Comment

You need to be a member of Fire Engineering Training Community to add comments!

Join Fire Engineering Training Community

Comment by Brian D Butler on January 30, 2018 at 2:34pm

Thanks Jeff,

This is about panel presence on the roof during attic (or cockloft) fires. We get a boatload of living space attic fires as our city is mostly 2 1/2 and 3 story frames. Solar panels are mostly on utility poles, but starting to see them on more and more urban homes. If there's going to be any ventilation,

I don't mind cutting lower than the highest point, especially in cocklofts, finished attics over knee wall void space where it's still pretty effective. Cutting by the peak where the danger of saw interference with any solar hardware is possible might be an issue. I recommend coming down "a little" to be safe.

Also, you do know who installs these solar panels in urban areas? In NJ you don't even need any license to do this. And the chances they abide by any code (like they'd even know) to allow us access is..well.."LOL" probably not happening.. 

If someone used foam on solar panels...I would drug test them...LOL.

I understand we can work around them, especially in garden apartment cocklofts, rowhomes, etc.. where we will take any cut we can get when working around them.

I take a class every year just to keep up with the changes (remember what they were telling us 8 years ago?) and I recommend the younger guys who will be dealing with them take your class at FDIC. 

I will be around that week, maybe I will attend. You still doing railroad response at FDIC?

Comment by Jeff Simpson on January 30, 2018 at 11:07am

Thanks Brother Butler for spreading the word.  Many of the items you mention will be discussed in my Solar Energy and the Fire Service class this April at FDIC International.  I few additional things to consider:

- Ventilation should occur at the highest point possible over the fire while avoiding damage to the solar modules

- UL recommends for fires involving energized solar modules, a fog stream should be applied at a safe distance of approximately 10 feet.

- Foam applications are not practical as a barrier to eliminate solar energy production by the solar modules and in most cases tarps are not effective. Also keep in mind the scene lighting will cause the solar modules to generate energy during night time operations.

- The 2015 International Fire Code (IFC), Section 605.11 addresses requirements for solar photovoltaic power

systems. Requires minimum setbacks for roof-mounted PV arrays to allow firefighters safe access, pathways and areas for smoke ventilation. Several exceptions exist so becoming familiar with the code and educating your building inspectors and fire marshals is critical.

Thanks,

Jeff

 

Policy Page

CONTRIBUTORS NOTE

Our contributors' posts are not vetted by the Fire Engineering technical board, and reflect the views and opinions of the individual authors. Anyone is welcome to participate.

For vetted content, please go to www.fireengineering.com/archives.

Fire Engineering Editor in Chief Bobby Halton
We are excited to have you participate in our discussions and interactive forums. Before you begin posting, please take a moment to read our policy page HERE. -- Bobby Halton

Be Alert for Spam
We actively monitor the community for spam, however some does slip through. Please use common sense and caution when clicking links. If you suspect you've been hit by spam, e-mail peterp@pennwell.com.

FE Talk Radio

Friday at 7:30 p.m. EDT

Networking for Success

with

Dave McGlynn

CALL IN AND JOIN THE SHOW

1-877-497-3973 (Toll Free)
or 1-760-454-8852

Check out the schedule of
UPCOMING SHOWS

Ricky Riley, Dan Shaw, Doug Mitchell & Nick Martin

© 2018   Created by fireeng.   Powered by

Badges  |  Report an Issue  |  Terms of Service