Fire Engineering Training Community

Where firefighters come to talk training

Can anyone post a photo of a truss marking system that has been enacted by law or ordinance?
Be Safe,

Views: 3492

Reply to This

Replies to This Discussion

Frank,
This is one that I found online.
Attachments:
Thanks, Scott

NYS 19 NYCRR Part 1264 - IDENTIFICATION OF BUILDINGS UTILIZING TRUSS TYPE CONSTRUCTION
http://www.dos.state.ny.us/code/trussID.htm


5.05 Signage of Buildings with Wood or Lightweight Steel Truss, or Composite Wood Joist (TJI) or Roof Construction
Reference: 2007 San Francisco Fire Code Section 507.3.2http://www.sfgov.org/site/sffd_page.asp?id=80083

Exterior Placard NJAC 5:70 - 2.20(a)1 and 2 This attachment was provided by the New Jersey Division of Fire Safety and is referenced as Exterior Placard NJAC 5:70 - 2.20(a)1 and 2.


Let me know if I can support any of your other needs on this...
Attachments:

NIOSH Suggested Truss Placard Type
Here's some additional info;
EXAMPLE LANGUAGE FOR A LAW REQUIRING LABELING OF BUILDINGS FOR THE FIRE SERVICE

This sample language is based on recommendations in the National Institute for Occupational Safety and Health (NIOSH) report entitled “NIOSH Alert: Preventing Injuries and Deaths of Firefighters due to Truss System Failures.”

The report states: “Consider placing building construction information outside the building. Include
information about roof and floor type…1
The NIOSH report also recommends as part of pre-fire planning to: Record data regarding roof and floor construction (e.g., wooden joist, wood truss, steel joist, steel truss, beam and girder, etc.) [NFPA 2003].2 The sample language below provides building labeling that identifies the building’s construction type, is simple yet logical, and should allow firefighters to quickly know the building’s floor and roof construction materials, promoting better and more complete information on the fireground and increased firefighter safety.
xxx Identification of structural construction. Structural construction types shall be identified by a sign or signs, in accordance with the provisions of this section.
xxx.1 Signs. Signs shall be affixed where a building or a portion thereof is classified as Group A, B, E, F, H, I, M, R-1, R-2, R-4 or S occupancy. The owner of the building shall be responsible for the installation of the sign.
xxx.2 New buildings and buildings being added to. Signs shall be provided in newly constructed buildings and in existing buildings where an addition that extends or increases the floor area of the building. Signs shall be affixed prior to the issuance of a certificate of occupancy or a certificate of compliance.
xxx.3 Existing buildings. Signs shall be provided in existing buildings. Signs shall be affixed within ninety days of being notified in writing by the Code Enforcement Official.
xxx.4 Contents of signs. Signs shall consist of a diagram (see Figure 1) 6 inches (152.4 mm)in height and width, with a stroke width of ¼ inch (6.4 mm). The sign background shall be reflective white in color. The diagram and contents shall be reflective red in color, conforming to Pantone matching system (PMS) #187. Where a sign is directly applied to a door or sidelight, it may be a permanent non-fading sticker or decal. Signs not directly applied to doors or sidelights shall be of sturdy, non-fading, weather resistant material.
xxx.5 Identification of construction classification. Signs shall contain the roman alphanumeric designation of the construction classification of the building, in accordance with the provisions for the classification of types of construction (types I through V) of the building code. The roman numeral designating construction classification shall be 1 inch (25.4 mm) minimum in height and have a stroke width of ¼ inch (6.4 mm) minimum, and it shall be reflective white in color on a background of reflective red.
xxx.6 Identification of year of construction. Signs shall indicate the building’s year of construction or major reconstruction. The arabic numeral indicating year of construction shall be 1 inch (25.4 mm) minimum in height and have a stroke width of ¼ inch (6.4 mm) minimum, and it shall be reflective white in color on a background of reflective red.
xxx.7 Identification of structural construction types. Signs shall contain the alphabetic designations identifying the structural construction types used in the building, as follows:
"W" shall mean sawn joist/rafter construction, wood members
"I" shall mean engineered I-joist construction, wood members
"S" shall mean steel construction
"T" shall mean truss type construction3
"C" shall mea
Here's Additional info from the State of Floida, 2008;

The Aldridge-Benge Firefighter Safety Act.
The law was named in honor of Orange County firefighters Todd Aldridge and Mark Benge, who died in 1989 after the truss roof of a gift shop collapsed. Under the new law, owners of any commercial, industrial or multi unit residential structure, have to clearly mark if their buildings have lightweight roof or floor trusses, allowing firefighters to change their tactics when working in the fire.

http://www.cfnews13.com/News/Local/2008/7/2/new_firefighter_protect... hese types of structures.

633.027 Buildings with light-frame truss-type construction; notice requirements; enforcement
(1) The owner of any commercial or industrial structure, or any multiunit residential structure of three units or more, that uses light-frame truss-type construction shall mark the structure with a sign or symbol approved by the State Fire Marshal in a manner sufficient to warn persons conducting fire control and other emergency operations of the existence of light-frame truss-type construction in the structure.
(2) The State Fire Marshal shall adopt rules necessary to implement the provisions of this section, including, but not limited to:
(a) The dimensions and color of such sign or symbol.
(b) The time within which commercial, industrial, and multiunit residential structures that use light-frame truss-type construction shall be marked as required by this section.
(c) The location on each commercial, industrial, and multiunit residential structure that uses light-frame truss-type construction where such sign or symbol must be posted.
(3) The State Fire Marshal, and local fire officials in accordance with s. 633.121, shall enforce the provisions of this section. Any owner who fails to comply with the requirements of this section is subject to penalties as provided in s. 633.161.

More from New York State.....
http://www.trussid.org/index.html
Attached is information from Wheeling, Illinois, who enacted thier own local code requriement. April 18, 1994 adopted Ordinance 2948 amending Title 14, Fire, of the Wheeling Municipal Code by adding Chapter 14.08 "Wood Truss Warning Signs"
Attachments:


State of New Jersey TRUSS SIGNS (Truss Roof And Truss Floor Assembly Signs)
Truss roof signs are required by the New Jersey State Uniform Fire Code for buildings, which utilize either a floor or roof assembly consisting of truss construction. A truss sign gives early warning to fire and emergency service members that the roof and/or floor may be subject to early collapse in the event of a fire condition.

ISOSCELES TRIANGLE SIGNS
N.J.A.C. 5:70-2.20(a)1.
"The emblem shall be of a bright and reflective color, or made of reflective material. The shape of the emblem shall be an isosceles triangle and the size shall be 12 inches horizontally by 6 inches vertically. With letters of a size and color to make them conspicuous, shall be printed on the emblem, as shown in images below."

N.J.A.C. 5:70-2.20(a)2
"The emblem shall be permanently affixed to the left of the main entrance door at the height of between 4 feet and 6 feet above the ground, and shall be installed and maintained by the owner of the building".


State of Vermont
See attachment for additional Info
Attachments:

CITY OF CHESAPEAKE, VA TRUSS ID PROGRAM; The above sticker is used for quick recognization of potential Collapse Dangers associated with TRUSS constructed buildings. The sticker is placed on every entry door of all commercial buildings with Truss construction.

The use of trusses in building construction presents a great danger to firefighting personnel when those structures are involved in fire conditions. By design, the truss members in floor and roof assemblies will collapse, without warning, after being exposed to heat or flame contact for a very short period of time. Because of the inherent danger firefighters must face while operating within these buildings, a Truss Identification Program (TIP) has been instituted to alert personnel of the danger prior to beginning fire suppression operations. The Truss Identification Program is intended to alert the members of the Chesapeake Fire Department with pertinent pre-plan information before firefighting forces are committed to an interior attack.

The TIP shall be an ongoing program applied to all commercial buildings inspected by the Chesapeake Fire Department. http://www.chesapeake.va.us/services/depart/fire/truss.shtml
Frank,
You can also check with New Jersey, they were the first state in the Union to enact such makings.

Be Safe,

Mike O
Thanks

Reply to Discussion

RSS

Policy Page

CONTRIBUTORS NOTE

Our contributors' posts are not vetted by the Fire Engineering technical board, and reflect the views and opinions of the individual authors. Anyone is welcome to participate.

For vetted content, please go to www.fireengineering.com/archive/.

Fire Engineering Editor in Chief Bobby Halton
We are excited to have you participate in our discussions and interactive forums. Before you begin posting, please take a moment to read our policy page. -- Bobby Halton

Be Alert for Spam
We actively monitor the community for spam, however some does slip through. Please use common sense and caution when clicking links. If you suspect you've been hit by spam, e-mail peter.prochilo@clarionevents.com.

FE Podcasts


Check out the most recent episode and schedule of
UPCOMING PODCASTS

© 2020   Created by fireeng.   Powered by

Badges  |  Report an Issue  |  Terms of Service